Nationally, the average water heater repair cost ranges between $120 and $200, although prices can range up to $400 or more. Water heater repair costs will depend on the type of water heater you have (tankless, electric, natural gas, etc.), the source of the problem, the cost for new parts, and labor rates in your area. Common water heater issues include problems with the thermocouple, thermostat, heating element and leaks. Most standard electric water heaters have two thermostats and two elements. One example for the cost to replace a bad thermostat is $185 for parts and labor. Replacing both the thermostat and the heating element could cost approximately $150-$200. The thermocouple is a safety device that senses when the pilot light is burning and signals the gas valve to close if the pilot light goes out. If your thermocouple is bad or corroded, the average cost to clean and repair it could be between $350 and $400. If your water heater has started to leak, it is usually more cost-effective to invest in a new water heater than to repair it, unless you’re covered by a warranty.
The thicknesses of the water pipe and tube walls can vary. Pipe wall thickness is denoted by various schedules or for large bore polyethylene pipe in the UK by the Standard Dimension Ratio (SDR), defined as the ratio of the pipe diameter to its wall thickness. Pipe wall thickness increases with schedule, and is available in schedules 20, 40, 80, and higher in special cases. The schedule is largely determined by the operating pressure of the system, with higher pressures commanding greater thickness. Copper tubing is available in four wall thicknesses: type DWV (thinnest wall; only allowed as drain pipe per UPC), type 'M' (thin; typically only allowed as drain pipe by IPC code), type 'L' (thicker, standard duty for water lines and water service), and type 'K' (thickest, typically used underground between the main and the meter). Because piping and tubing are commodities, having a greater wall thickness implies higher initial cost. Thicker walled pipe generally implies greater durability and higher pressure tolerances.
There are few things more frustrating than a clogged or slow drain—or, even worse, an overflowing sink or tub because the drainage is backing up. At Len The Plumber, we can solve any of your slow or clogged drain problems. If you notice many of your drains are having problems, the problem could lie with your main sewer line. But don’t worry—we can handle that, too!
Cracked sewer pipes can be more than just a costly repair—they can result in extensive and pricey property damage and lead to serious health risks. Sewer line repair is the first line of defense when a sewer line fails. If the sewer line can’t be repaired, sewer line replacement is the only other option. Luckily, Mr. Rooter® Plumbing is your local source for quality sewer repair and replacement at any time.
Present-day water-supply systems use a network of high-pressure pumps, and pipes in buildings are now made of copper, brass, plastic (particularly cross-linked polyethylene called PEX, which is estimated to be used in 60% of single-family homes), or other nontoxic material. Due to its toxicity, most cities moved away from lead water-supply piping by the 1920s in the United States, although lead pipes were approved by national plumbing codes into the 1980s, and lead was used in plumbing solder for drinking water until it was banned in 1986. Drain and vent lines are made of plastic, steel, cast-iron, or lead.
Eduardo came out very quickly and snaked the kitchen sink with great expertise. He recommended I have a cleanout installed and offered me a great price but since I live in apartment there wouldn't be too much long term benefit for me personally since I plan on moving out soon. I will be keeping his number handy though as I will be calling him in the future for any problems we have might. Thanks again Eduardo!
Cast iron and ductile iron pipe was long a lower-cost alternative to copper, before the advent of durable plastic materials but special non-conductive fittings must be used where transitions are to be made to other metallic pipes, except for terminal fittings, in order to avoid corrosion owing to electrochemical reactions between dissimilar metals (see galvanic cell).
Water systems of ancient times relied on gravity for the supply of water, using pipes or channels usually made of clay, lead, bamboo, wood, or stone. Hollowed wooden logs wrapped in steel banding were used for plumbing pipes, particularly water mains. Logs were used for water distribution in England close to 500 years ago. US cities began using hollowed logs in the late 1700s through the 1800s. Today, most plumbing supply pipe is made out of steel, copper, and plastic; most waste (also known as "soil") out of steel, copper, plastic, and cast iron.
TCR Rooter and Plumbing Repair has been providing professional service for our customers since 1993, and maintain the same quality of service for you today. Your satisfaction is our goal and we work hard to provide you with the best service in Northern Arizona. With our skilled team of certified, professional plumbers, we work to provide you with smart, satisfactory work for all your plumbing needs. New construction, remodels, leak repairs, sewer and water line replacements, water heaters, and any and all other service needs or emergencies you may have, we have your back. Look through our website or give us a call for more information on the services we provide and see what we could do for you.